Product Categories

  • Marine Anodes
  • Marine Auxiliary Machinery
  • Marine Deck Machinery
  • Marine Decorative Materials
  • Marine Electric Equipment
  • Marine Flanges
  • Marine Galley And Laundry Equipment
  • Marine HVAC Systems
  • Marine Instruments
  • Marine Mooring Equipment
  • Marine Outfitting Equipment
  • Marine Pipe Fittings
  • Marine Propulsion & Shaft & Rudder System
  • Marine pump
  • Marine Safety Equipment-LSA&FFE
  • Marine Valves
  • Container
  • Dredging Equipment
  • Fishing Equipment
  • Lifting&Rigging Equipment
  • Shipbuilding Plate And Section
  • CB/T 3943-2002 SUS 304 Marine SDNR Valve Type A/AS

    Overview
    The A and AS types are straight-pattern flanged stainless steel stop check valves built for combined isolation and backflow prevention duty in shipboard piping systems handling seawater, fresh water and corrosive media.
    Both share one valve body design; the difference is the flange interface — the A type is drilled to GB 569, the AS type to GB 2501. The range covers PN1.0 / PN1.6 / PN2.5 / PN4.0 / PN6.4, with DN20-500 available. Manual handwheel operation, bolted bonnet, and a metal-seated disc deliver dual performance: the handwheel can positively close the valve for isolation, while the free disc automatically closes to block reverse flow when the stem is lifted, offering predictable protection under marine corrosive service conditions.Material selection follows the medium, not the price list. Body, bonnet and all internal trim are stainless steel, typically 06Cr19Ni10 (304) or 022Cr19Ni10 (316L) for marine seawater and corrosive service; the metal-on-metal seating structure resists galling and marine corrosion without a soft seat insert. Packing and gasket are PTFE for water and general corrosive service. Stainless steel construction provides excellent resistance to pitting and crevice corrosion in seawater and chemical media.Every valve is designed, manufactured and accepted against CB/T 3943-2002, with strength, tightness, wall thickness, dimensional and geometric tolerances referenced to GB/T 600—2023. Mass is controlled to within +4 % of theoretical, castings are traceable by heat number for a minimum of three years, and marking follows GB/T 3032. Clause-by-clause verification data is listed in the compliance section below.
    Basic Sructure Of SUS 304 Marine SDNR Valve Type A/AS

     

     

     

     

     

     

     

    Basic parameters (CB/T 3943-2002)

    Type Nominal Pressure PN

    MPa

    Operating Temperature, ℃ Nominal Diameter DN

    mm

    Flange Standard Applicable Media Installation
    ≤20 100 150 200 250 300 350  Seawater, fresh water, fuel oil, lube oil Horizontal / vertical, flow upward
    Maximum Allowable Working Pressure P, MPa
    A 1.0 0.95 0.86 0.81 0.76 0.71 0.66 0.36 65~150 GB 569
    1.6 1.52 1.31 1.29 1.21 1.13 1.06 1.01 125, 150 GB 569
    2.5 2.38 2.15 2.01 1.89 1.77 1.66 1.59 20~150 GB 569
    4.0 3.80 3.44 3.22 3.02 2.83 2.65 2.54 65~100 GB 569
    6.4 5.69 5.26 4.96 4.68 4.41 4.16 3.92 20~50 GB 569
    AS 0.6 0.57 0.52 0.48 0.45 0.42 0.40 0.38 15~300 GB 2501
    1.0 0.95 0.86 0.81 0.76 0.71 0.66 0.63 200~300 GB 2501
    1.6 1.52 1.31 1.29 1.21 1.13 1.06 1.01 100~300 GB 2501
    2.5 2.38 2.15 2.01 1.89 1.77 1.66 1.59 15~300 GB 2501
    4.0 3.80 3.44 3.22 3.02 2.83 2.65 2.54 65~100 GB 2501
    6.4 5.69 5.26 4.96 4.68 4.41 4.16 3.92 20~50 GB 2501

    Working Principle
    This stop check valve combines stop and check valve functions.Raise the stem: the disc opens for forward flow and automatically closes to prevent backflow upon reverse pressure.Lower the stem to press the disc tightly against the seat for positive manual shut-off.
    Basic Dimensions of SUS 304 Marine SDNR Valve Type A(CB/T 3943-2002) PN 1.0, 1.6 and 2.5 MPa

    Nominal Pressure PN, MPa Nominal Diameter DN Structural Dimensions Wall Thickness t Flange Bolt Handwheel Lift Range Weight kg
    Type A
    L

    Type A

    H≈

    Type A

    D D₁ D₂ d₀ b n Qty. Th. D₀ S m
     


    1.0

    65 290 310 6 155 123 104 15 14 6 M14 140 12 18 14.5
    80 310 345 6 170 138 118 15 14 8 M14 160 14 24 16.8
    100 350 374 6 190 158 138 15 14 8 M14 180 14 25 24.6
    125 400 426 7 215 183 164 15 14 10 M14 200 17 32 34.2
    150 480 487 7 240 208 190 15 14 12 M14 200 17 38 46.3
    1.6 125 400 465 8 225 187 168 17 15 10 M16 250 22 32 44.3
    150 480 524 8 255 217 196 17 15 12 M16 280 24 38 56.9
     

     

     


    2.5

    20 150 217 5 95 68 48 13 12 4 M12 80 8 7 3.8
    25 160 217 5 105 73 56 13 12 4 M12 80 8 7 4.6
    32 180 236 5 115 83 64 13 12 4 M12 100 9 9 6.4
    40 200 260 6 125 93 74 15 13 6 M14 120 11 11 8.7
    50 230 288 6 135 103 84 15 13 6 M14 140 12 14 10.9
    65 290 335 7 170 132 110 17 16 8 M16 160 14 18 17.6
    80 310 366 7 185 147 126 17 16 8 M16 200 17 24 24.6
    100 350 417 8 205 167 146 17 16 8 M16 250 22 25 33.8
    125 400 493 9 240 196 172 21 20 10 M20 280 24 32 49.2
    150 500 556 9 270 226 200 21 20 12 M20 320 27 38 67.3

    Basic Dimensions of SUS 304 Marine SDNR Valve Type A(CB/T 3943-2002)PN 4.0 and 6.4 MPa

    Nominal Pressure PN, MPa Nominal Diameter DN Structural Dimensions Wall Thickness t Flange

    Bolt Handwheel Lift Range Weight kg
    Type A
    L Type A H≈ Type A D D₁ D₂ D₃ D₄ f d₀ b n Qty. Th. D₀ S m
    4.0 65 310 409 8 175 137 118 110 94 3 17 18 8 M16 250 22 19 35.2
    80 350 436 9 190 152 130 121 105 3 17 18 8 M16 250 22 23 39.1
    100 400 466 9 225 181 157 150 128 4 21 21 10 M20 280 24 28 53.1
     


    6.4

    20 160 261 7 105 73 58 51 35 3 13 13 6 M12 100 9 7 7.7
    25 180 272 7 115 83 66 58 42 3 15 15 6 M14 100 9 7 8.7
    32 200 304 7 125 93 74 66 50 3 15 17 6 M14 120 11 9 10.3
    40 230 334 7 145 107 84 76 60 3 17 19 6 M16 160 14 12 17.7
    50 250 354 8 155 117 96 88 72 3 17 20 6 M16 180 14 15 22.3

    Basic Dimensions of SUS 304 Marine SDNR Valve Type AS, PN 0.6, 1.0, 1.6 and 2.5 MPa

    Nominal Pressure PN, MPa Nominal Diameter DN Structural Dimensions Wall Thickness t Flange


    Bolt Handwheel Lift Range Weight kg

    Type AS

    L Type AS H≈ Type AS D D₁ D₂ d₀ b n Qty. Th. D₀ S m
     

     

     

    0.6

    15 130 217 4 80 55 40 11 12 4 M10 80 8 7 3.6
    20 150 217 4 90 65 50 11 14 4 M10 80 8 7 4.4
    25 160 217 4 100 75 60 11 14 4 M10 80 8 7 5.1
    32 180 236 5 120 90 70 14 16 4 M12 100 9 9 6.4
    40 200 260 5 130 100 80 14 16 4 M12 120 11 11 8.5
    50 230 288 6 140 110 90 14 16 4 M12 140 12 14 10.6
    65 290 335 6 160 130 110 14 16 4 M12 160 12 18 16.7
    80 310 362 6 190 150 128 14 18 8 M16 160 14 24 22.2
    100 350 417 7 210 170 148 18 20 8 M16 180 14 25 33.4
    125 400 493 7 240 200 178 18 20 8 M16 200 17 32 45.1
    150 480 556 7 265 225 202 18 22 8 M16 200 17 38 67.5
    200 600 675 9 320 280 258 22 24 12 M20 250 22 50 98.3
    250 730 721 9 375 335 312 22 24 12 M20 280 24 60 162.0
    300 850 821 9 440 395 365 24 26 12 M20 320 27 75 220.0
    1.0 200 600 621 10 340 295 268 22 24 8 M20 360 27 50 107.0
    250 730 721 11 395 350 320 22 26 12 M20 450 32 60 165.0
    300 850 821 11 445 400 370 22 26 12 M20 500 36 75 223.0
     

    1.6

    100 350 417 8 220 180 158 18 22 8 M16 250 22 25 35.4
    125 400 493 8 250 210 184 18 22 8 M16 280 24 32 50.5
    150 480 556 9 285 240 212 22 24 8 M20 320 27 38 67.3
    200 600 621 9 340 295 268 22 24 8 M20 450 32 50 121.0
    250 730 721 11 405 355 320 26 26 12 M24 500 36 60 167.2
    300 850 821 11 460 410 370 26 28 12 M24 500 36 75 215.0
     

    2.5

    15 130 217 5 95 65 47 14 14 4 M12 80 8 7 4.6
    20 150 217 5 105 75 58 14 16 4 M12 80 8 7 4.9
    25 160 217 5 115 85 68 14 16 4 M12 80 8 7 5.7
    32 180 236 6 140 100 78 18 18 4 M16 100 9 9 8.9
    40 200 260 6 150 110 88 18 18 4 M16 120 11 11 10.6
    50 230 288 7 165 125 102 18 20 4 M16 140 12 14 14.2
    65 290 335 7 185 145 122 22 22 8 M16 160 14 18 21.9
     

     

     

    2.5

    80 310 366 7 200 160 133 22 24 8 M20 200 17 24 28.4
    100 350 427 8 235 190 158 22 24 8 M20 250 22 25 39.5
    125 400 493 8 270 220 184 26 26 8 M20 280 24 32 57.3
    150 480 556 8 300 250 212 26 28 8 M24 320 27 38 75.9
    200 600 621 10 360 310 278 30 30 12 M24 450 32 50 129.0
    250 730 721 11 425 370 335 30 32 12 M27 500 36 60 167.2
    300 850 821 11 485 430 390 30 34 16 M27 500 36 75 215.0

    Basic Dimensions of SUS 304 Marine SDNR Valve Type AS, PN 0.6, 1.0, 1.6 and 2.5 MPa PN 4.0 and 6.4 MPa

    Nominal Pressure PN, MPa Nominal Diameter DN Structural Dimensions Wall Thickness t Flange
    Bolt Handwheel Lift Range Weight kg
    Type AS
    L Type AS H≈ Type AS D D₁ D₂ D₃ D₄ f d₀ b n Qty. Th. D₀ S m
     

    4.0

    65 290 409 8 185 145 122 110 94 3 18 22 8 M16 250 22 19 37.8
    80 310 436 9 200 160 133 121 105 3 18 24 8 M16 250 22 23 42.9
    100 350 466 9 235 190 158 150 128 3 22 24 8 M20 280 24 28 54.1
     


    6.4

    20 — 261 7 130 90 58 51 35 3 18 22 4 M16 100 9 7 9.3
    25 230 272 7 140 100 68 58 42 3 18 24 4 M16 100 9 7 11.0
    32 — 304 7 155 110 78 66 50 3 18 24 4 M16 120 11 9 13.1
    40 260 334 7 170 125 88 76 60 3 22 26 4 M20 160 14 12 21.7
    50 300 354 8 180 135 102 88 72 3 22 26 4 M20 180 14 15 27.2

    Materials of Principle Parts(CB/T 3943-2002)

    Part Name Material
    Name Grade Standard No.
    Valve body, bonnet, disc Stainless steel ZG0Cr18Ni9 GB/T2100-1980
    ZG00Cr17Ni14Mo3 Material and Welding Code (1998)
    Valve stem, fasteners Stainless steel 0Cr13 GB/T1220-1992
    Packing, gasket PTFE — —
    Hardfaced seat for PN≥4.0 MPa Cobalt‑chromium‑tungsten hard alloy — —

    Selection & Installation Key Points
    1.Selection: For seawater, fresh water and compatible low-temperature media, PN ≤6.4 MPa. Complies with CB/T3943-2002 Marine Flanged Stainless Steel Stop-Check Valve standard. Select according to pipeline size; confirm stainless steel wetted parts for marine corrosion resistance.
    2.Installation orientation: Can be installed horizontally or vertically. Keep the valve mark of flow direction consistent with pipeline flow direction. Reserve sufficient surrounding space for adjustment and maintenance. FORBIDDEN: Do not use for throttling for long time.
    3.Sealing pair: Cobalt-chromium-tungsten hard alloy hardfaced sealing surface for PN≥4.0MPa, suitable for water and low-temperature medium. Avoid sand, metal debris and hard impurities scratching the sealing surface.
    4.Temp-pressure: Rated pressure applies at normal temperature. Temperature rise affects sealing performance; keep operating pressure and temperature below the rated value of selected grade. This valve adapts to working temperature down to -165℃.
    5.Flow & clearance: Unidirectional flow. It can cut off flow manually and prevent backflow automatically. Isolate upstream medium by closing the front stop valve before disassembly; avoid medium leakage.
    Why this SUS 304 Marine SDNR Valve
    One integrated structure: The stainless steel valve body and bonnet are the main components. Rotating the handwheel drives the stem and disc to open or close the passage, and it can automatically block reverse flow when medium backflows. Flange connection complying with GB/T569, compact structure, reliable sealing and easy operation. It is a combined cut-off & non-return component for marine seawater, fresh water and low-temperature pipelines of chemical tankers, LNG carriers and vessels. The internal flow channel is specially designed for ship service system. The hard alloy sealing pair features excellent seawater corrosion resistance, good low-temperature toughness, long service life and good tightness. The valve can be disassembled for inspection and replacement of wearing parts, without heavy dismantling of adjacent pipelines. Wetted materials: ZG0Cr18Ni9 / ZG00Cr17Ni14Mo3 stainless steel body & bonnet, 0Cr13 stem and fasteners, PTFE packing and gasket, cobalt-chromium-tungsten hard alloy hardfacing for PN≥4.0MPa. What it is not: a throttling component. It is only for medium cut-off and backflow prevention; long-time throttling will cause rapid wear to the sealing surface.

    Related Products

    Send Inquiry

    If you have any questions about our products or services, feel free to reach out to customer service team.

    Scroll to Top