Application
GB/T 584 Type B/BS flanged cast steel stop valves are the right-angle members of the same family: the body turns the flow through 90° and shuts it in one casting. Body and bonnet are ZG275-485 cast steel, the seat is a lapped metal-to-metal pair with a weld-deposited stainless facing, the stem is 20Cr13 running in a back-seated bonnet, and both ends are flanged to the Chinese national shipbuilding standards. Steam, fuel oil, lubricating oil, fresh water and compressed air are all held tight at up to 300 °C, and up to 400 °C in PN40 and PN63.
What the angle body buys is a shorter job. Where the pipe has to turn anyway, one valve does the work of a straight valve plus an elbow: one body casting instead of two, two gasketed joints instead of four, two fewer places to leak, 4 to 18 % less weight hanging on the pipe, and a vertical stem with the handwheel where a hand can actually reach it. In an engine room that is usually the difference between a line that assembles as drawn and one that needs a spool piece made on board.
Basic structure of Marine Cast Steel Flanged Stop Valves Type B/BS

Type B/BS is the angle-pattern half of the GB/T 584 range. Bonnet, disc, stem, seat facing, packing, gasket, handwheel and marking are common with Type A/AS; the body casting is the only part that changes. Inlet flange on the pipe run, outlet turned 90°, handwheel on top of the bonnet: the disc travels at right angles to the inlet axis, so the seat sees the same lapped, line-contact shut-off as the straight pattern while the body absorbs the bend. Parts: 1 body, 2 disc, 3 bonnet, 4 stem, 5 gasket, 6 packing, 7 stud bolt, 8 nut, 9 handwheel.
| PN | Max. working pressure (MPa) |
Type B DN range |
Type BS DN range |
Service media |
|---|---|---|---|---|
| 10 | 1.0 | 65 – 150 | 200 – 300 | Fresh water, lubricating oil, fuel oil, air and steam not exceeding 300 °C |
| 16 | 1.6 | 125 – 150 | 65 – 300 | |
| 25 | 2.5 | 20 – 150 | 15 – 200 | |
| 40 | 4.0 | 65 – 100 | 65 – 100 | Fresh water, lubricating oil, fuel oil, air and steam not exceeding 400 °C |
| 63 | 6.3 | 20 – 50 | 20 – 50 |
| PN | DN | L | H ≈ | H1 | t | D | D1 | D2 | d0 | b | n | Th. | D0 | S | Disc lift | Weight kg |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 10 | 65 | 115 | 277 | 115 | 6 | 155 | 123 | 104 | 15 | 14 | 6 | M14 | 140 | 12 | 19 | 13.9 |
| 80 | 125 | 304 | 125 | 7 | 170 | 138 | 118 | 15 | 14 | 8 | M14 | 160 | 14 | 26 | 17.9 | |
| 100 | 150 | 325 | 135 | 8 | 190 | 158 | 138 | 15 | 14 | 8 | M14 | 180 | 14 | 35 | 24.2 | |
| 125 | 175 | 366 | 155 | 8 | 215 | 183 | 164 | 15 | 14 | 10 | M14 | 200 | 17 | 44 | 35.4 | |
| 150 | 180 | 415 | 160 | 9 | 240 | 208 | 190 | 15 | 14 | 12 | M14 | 200 | 17 | 57 | 44.0 | |
| 16 | 125 | 175 | 405 | 155 | 8 | 225 | 187 | 168 | 17 | 15 | 10 | M16 | 250 | 22 | 44 | 47.2 |
| 150 | 180 | 452 | 160 | 9 | 255 | 217 | 196 | 17 | 15 | 12 | M16 | 280 | 24 | 57 | 61.8 | |
| 25 | 20 | 75 | 203 | 75 | 6 | 95 | 68 | 48 | 13 | 11 | 4 | M12 | 80 | 8 | 7 | 4.9 |
| 25 | 80 | 203 | 80 | 6 | 105 | 73 | 56 | 13 | 11 | 4 | M12 | 80 | 8 | 7 | 5.5 | |
| 32 | 85 | 216 | 85 | 6 | 115 | 83 | 64 | 15 | 13 | 6 | M14 | 100 | 9 | 9 | 6.5 | |
| 40 | 90 | 236 | 90 | 7 | 125 | 93 | 74 | 15 | 13 | 6 | M14 | 120 | 11 | 11 | 8.7 | |
| 50 | 95 | 258 | 95 | 7 | 135 | 103 | 84 | 15 | 13 | 6 | M14 | 140 | 12 | 14 | 11.0 | |
| 65 | 115 | 300 | 115 | 7 | 170 | 132 | 110 | 17 | 15 | 8 | M16 | 160 | 14 | 18 | 17.7 | |
| 80 | 125 | 325 | 125 | 7 | 185 | 147 | 126 | 17 | 16 | 8 | M16 | 200 | 17 | 24 | 21.9 | |
| 100 | 150 | 378 | 135 | 8 | 205 | 167 | 146 | 17 | 15 | 8 | M16 | 250 | 22 | 35 | 32.9 | |
| 125 | 175 | 433 | 155 | 9 | 240 | 196 | 172 | 21 | 19 | 10 | M20 | 280 | 24 | 44 | 58.4 | |
| 150 | 200 | 484 | 175 | 9 | 270 | 226 | 200 | 21 | 19 | 12 | M20 | 320 | 27 | 57 | 66.4 |
| PN | DN | L | H ≈ | H1 | t | D | D1 | D2 | D3 | D4 | f | d0 | b | n | Th. | D0 | S | Disc lift | Weight kg |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 40 | 65 | 125 | 374 | 125 | 8 | 175 | 137 | 118 | 110 | 94 | 3 | 17 | 18 | 8 | M16 | 250 | 22 | 17 | 32.9 |
| 80 | 140 | 394 | 130 | 9 | 190 | 152 | 130 | 121 | 105 | 3 | 17 | 18 | 8 | M16 | 250 | 22 | 20 | 34.8 | |
| 100 | 165 | 416 | 145 | 9 | 225 | 181 | 157 | 150 | 128 | 4 | 21 | 21 | 10 | M20 | 280 | 24 | 25 | 44.7 | |
| 63 | 20 | 80 | 243 | 85 | 7 | 105 | 73 | 58 | 51 | 35 | 3 | 13 | 13 | 6 | M12 | 100 | 9 | 7 | 7.1 |
| 25 | 85 | 253 | 90 | 7 | 115 | 83 | 66 | 58 | 42 | 3 | 13 | 15 | 6 | M14 | 100 | 9 | 7 | 8.3 | |
| 32 | 90 | 281 | 95 | 7 | 125 | 93 | 74 | 66 | 50 | 3 | 15 | 17 | 6 | M14 | 120 | 11 | 9 | 10.2 | |
| 40 | 105 | 310 | 110 | 7 | 145 | 107 | 84 | 76 | 60 | 3 | 15 | 19 | 6 | M14 | 160 | 14 | 11 | 16.4 | |
| 50 | 110 | 323 | 115 | 8 | 155 | 117 | 96 | 88 | 72 | 3 | 17 | 20 | 6 | M16 | 180 | 14 | 13 | 20.5 |
| PN | DN | L | H ≈ | H1 | t | D | D1 | D2 | d0 | b | n | Th. | D0 | S | Disc lift | Weight kg |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 10 | 200 | 275 | 543 | 275 | 10.0 | 340 | 295 | 268 | 22 | 24 | 8 | M20 | 360 | 27 | 68 | 109.0 |
| 250 | 325 | 623 | 325 | 11.5 | 395 | 350 | 320 | 22 | 26 | 12 | M20 | 450 | 32 | 80 | 168.0 | |
| 300 | 375 | 695 | 375 | 13.0 | 445 | 400 | 370 | 22 | 26 | 12 | M20 | 500 | 36 | 100 | 227.0 | |
| 16 | 65 | 145 | 300 | 145 | 7.0 | 185 | 145 | 122 | 18 | 18 | 8 | M16 | 160 | 14 | 18 | 20.9 |
| 80 | 155 | 325 | 155 | 8.0 | 200 | 160 | 138 | 18 | 20 | 8 | M16 | 200 | 17 | 24 | 25.7 | |
| 100 | 175 | 378 | 175 | 8.0 | 220 | 180 | 158 | 18 | 20 | 8 | M16 | 250 | 22 | 35 | 38.0 | |
| 125 | 200 | 395 | 200 | 8.0 | 250 | 210 | 188 | 18 | 22 | 8 | M16 | 250 | 22 | 44 | 48.4 | |
| 150 | 225 | 452 | 225 | 9.0 | 285 | 240 | 212 | 22 | 22 | 8 | M20 | 280 | 24 | 57 | 65.2 | |
| 175 | 225 | 505 | 225 | 10.0 | 315 | 270 | 242 | 22 | 24 | 8 | M20 | 360 | 27 | 60 | 92.2 | |
| 200 | 275 | 565 | 275 | 10.0 | 340 | 295 | 268 | 22 | 24 | 8 | M20 | 450 | 32 | 68 | 122.0 | |
| 250 | 325 | 646 | 325 | 11.5 | 405 | 355 | 320 | 26 | 26 | 12 | M24 | 500 | 36 | 80 | 182.0 | |
| 300 | 375 | 760 | 375 | 13.0 | 460 | 410 | 378 | 26 | 28 | 12 | M24 | 560 | 36 | 100 | 234.0 | |
| 25 | 15 | 90 | 203 | 90 | 6.0 | 95 | 65 | 45 | 14 | 16 | 4 | M12 | 80 | 8 | 7 | 5.2 |
| 20 | 95 | 203 | 95 | 6.0 | 105 | 75 | 58 | 14 | 18 | 4 | M12 | 80 | 8 | 7 | 5.7 | |
| 25 | 100 | 203 | 100 | 6.0 | 115 | 85 | 68 | 14 | 18 | 4 | M12 | 80 | 8 | 7 | 6.4 | |
| 32 | 105 | 216 | 105 | 6.0 | 140 | 100 | 78 | 14 | 18 | 4 | M12 | 100 | 9 | 9 | 8.7 | |
| 40 | 115 | 236 | 115 | 6.0 | 150 | 110 | 88 | 14 | 18 | 4 | M12 | 120 | 11 | 11 | 11.5 | |
| 50 | 125 | 245 | 125 | 7.0 | 165 | 125 | 102 | 18 | 20 | 4 | M16 | 140 | 12 | 14 | 14.9 | |
| 65 | 145 | 300 | 145 | 7.0 | 185 | 145 | 122 | 18 | 22 | 8 | M16 | 160 | 14 | 18 | 21.6 | |
| 80 | 155 | 325 | 155 | 8.0 | 200 | 160 | 138 | 18 | 24 | 8 | M16 | 200 | 17 | 24 | 27.1 | |
| 100 | 175 | 378 | 175 | 8.0 | 235 | 190 | 162 | 22 | 24 | 8 | M20 | 250 | 22 | 35 | 39.7 | |
| 125 | 200 | 433 | 200 | 9.0 | 270 | 220 | 188 | 26 | 26 | 8 | M24 | 280 | 24 | 44 | 61.0 | |
| 150 | 225 | 484 | 225 | 9.0 | 300 | 250 | 218 | 26 | 28 | 8 | M24 | 320 | 27 | 57 | 77.4 | |
| 200 | 275 | 620 | 275 | 11.5 | 360 | 310 | 278 | 26 | 30 | 12 | M24 | 450 | 32 | 68 | 133.0 |
| PN | DN | L | H ≈ | H1 | t | D | D1 | D2 | D3 | D4 | f | d0 | b | n | Th. | D0 | S | Disc lift | Weight kg |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 40 | 65 | 145 | 374 | 145 | 8 | 185 | 145 | 122 | 110 | 94 | 3 | 18 | 22 | 8 | M16 | 250 | 22 | 17 | 36.4 |
| 80 | 155 | 394 | 155 | 9 | 200 | 160 | 138 | 121 | 105 | 3 | 18 | 24 | 8 | M16 | 250 | 22 | 20 | 40.3 | |
| 100 | 175 | 416 | 175 | 9 | 235 | 190 | 162 | 150 | 128 | 3 | 22 | 24 | 8 | M20 | 280 | 24 | 25 | 51.5 | |
| 63 | 20 | 115 | 243 | 115 | 7 | 130 | 90 | 58 | 51 | 35 | 3 | 18 | 22 | 4 | M16 | 100 | 9 | 7 | 8.5 |
| 25 | 115 | 253 | 115 | 7 | 140 | 100 | 68 | 58 | 42 | 3 | 18 | 24 | 4 | M16 | 100 | 9 | 7 | 10.5 | |
| 32 | 130 | 275 | 130 | 7 | 155 | 110 | 78 | 66 | 50 | 3 | 22 | 24 | 4 | M20 | 120 | 11 | 9 | 12.8 | |
| 40 | 130 | 310 | 130 | 7 | 170 | 125 | 88 | 76 | 60 | 3 | 22 | 26 | 4 | M20 | 160 | 14 | 11 | 20.6 | |
| 50 | 150 | 323 | 150 | 8 | 180 | 135 | 102 | 88 | 72 | 3 | 22 | 26 | 4 | M20 | 180 | 14 | 13 | 25.8 |
| Part | Item | Material | Grade | Standard |
|---|---|---|---|---|
| Body | Body casting | Cast steel | ZG275-485 | GB/T 12229—2025 |
| Body seating face | Stainless steel, weld-deposited | E347 | GB/T 983—2012 | |
| Bonnet | Bonnet casting | Cast steel | ZG275-485 | GB/T 12229—2025 |
| Back-seat face | Stainless steel, weld-deposited | E347 | GB/T 983—2012 | |
| Disc | Disc | Quality carbon steel | 20 | GB/T 699—2015 |
| Disc seating face | Stainless steel, weld-deposited | E410 | GB/T 983—2012 | |
| Stem | Stem | Stainless steel | 20Cr13 | GB/T 1220—2007 |
| Packing | Option 1 | PTFE braided packing | F4SD | JB/T 6626—2011 |
| Option 2 | Flexible graphite | RSM | CB/T 3589—1994 | |
| Gasket | Option 1 | PTFE | PTFE | QB/T 4041—2010 |
| Option 2 | Flexible graphite | RSM | CB/T 3589—1994 | |
| Fasteners | Stud bolt | Property class 6.8 | Property class 6.8 | GB/T 898—1988 |
| Nut | Property class 6 | Property class 6 | GB/T 6170—2015 | |
| Handwheel | Option 1 | Cast steel | ZG230-450 | CB/T 3530—1993 |
| Option 2 | Ductile iron | QT400-15 | CB/T 3530—1993 |
When the line carries fuel oil or steam, flexible graphite shall be used for both packing and gasket. A cast steel handwheel is usual for type B; a ductile iron handwheel for type BS.
| Type | Flange standard | L | H ≈ | D | D1 | D2 | d0 | b | n | Th. | Weight kg |
|---|---|---|---|---|---|---|---|---|---|---|---|
| A | CB/T 4196—2011 | 230 | 288 | 135 | 103 | 84 | 15 | 13 | 6 | M14 | 11.8 |
| AS | GB/T 9124.1—2019 | 230 | 275 | 165 | 125 | 102 | 18 | 20 | 4 | M16 | 15.2 |
| B | CB/T 4196—2011 | 95 | 258 | 135 | 103 | 84 | 15 | 14 | 6 | M14 | 11.0 |
| BS | GB/T 9124.1—2019 | 125 | 245 | 165 | 125 | 102 | 18 | 20 | 4 | M16 | 14.9 |
FAQ — what buyers ask before the first order
Match the flange on the pipe: CB/T 4196 for type B, GB/T 9124.1 for type BS. Same DN and same PN do not mean the same bolt circle.
What sizes and classes can you supply?
DN15 to DN300, PN10 to PN63. Not every size is made in every class — the DN range column in the basic parameters table is the limit.
Why this valve
Built to the standard, ZG275-485 cast steel body and bonnet, a lapped metal-to-metal seat with stainless weld-deposited facing, precision-machined disc and 20Cr13 stem — the materials GB/T 584—2026 calls up, in the grades it calls up.
That is what holds tight in steam, fuel oil, lubricating oil, fresh water and compressed air: shut-off up to 300 °C, and to 400 °C in PN40 and PN63, with smooth handwheel operation throughout.
The angle body is the reason to choose this pattern. The turn and the isolation are one casting, so the elbow and its two joints come out of the line, the weight on the pipe drops, and the stem stays vertical with the handwheel where it can be worked.
Two flange patterns, one range. CB/T 4196—2011 for type B, GB/T 9124.1—2019 for type BS — DN15 to DN300, PN10 to PN63, from the same design.
Tell us the pipe standard, the size, the medium and the temperature — the designation follows from there.


