Overview
B and BS are angle-type flanged check valves to GB/T 592—2026 for marine seawater, fresh water, lube oil and fuel oil lines. They turn flow 90° and close on reverse flow, protecting pumps in tight pump-room layouts. The center-to-end dimension sets the mounting envelope; check it before piping.
Body selection follows the duty. HT200 gray iron is the cost-effective default for fresh water and lube oil at normal duty. QT400-18 ductile iron suits higher shock loads, where longer service life offsets a higher initial material cost. Tin bronze trim resists wear; the aluminum-bronze seat needs de-alloying control in seawater.
All valves are built and verified to GB/T 592—2026 against GB/T 600—2023. Strength, tightness, dimensions and assembly are checked under one controlled system. Each melt keeps at least three marked test bars for three years, giving full traceability for class and owner review.
Quick Selection Guide
Flange standard — B vs BS
Type B: CB/T 4196—2011 flange.
Type BS: GB/T 9124.1—2019 flange.
Body material — HT200 vs QT400-18
HT200 gray iron: cost-effective default for fresh water / lube oil, normal duty.
QT400-18 ductile iron: recommended when shock load and mechanical margin dominate, or when downtime cost exceeds initial material cost.

| Type | PN | Max working pressure (MPa) | DN | Medium | Flange standard |
|---|---|---|---|---|---|
| B | 10 | 1.0 | 65–150 | Sea water / fresh water / lube oil / fuel oil | CB/T 4196—2011 |
| B | 16 | 1.6 | 20–50 | Sea water / fresh water / lube oil / fuel oil | CB/T 4196—2011 |
| BS | 6 | 0.6 | 50–150 | Sea water / fresh water / lube oil / fuel oil | GB/T 9124.1—2019 |
| BS | 10 | 1.0 | 65–150 | Sea water / fresh water / lube oil / fuel oil | GB/T 9124.1—2019 |
| BS | 16 | 1.6 | 20–50 | Sea water / fresh water / lube oil / fuel oil | GB/T 9124.1—2019 |
Note: For fuel oil service, gasket and packing shall be flexible graphite. Type B has no PN6 rating. Dimensions in mm; pressure in MPa.
Marine Cast Iron Flanged Check Valves (GB/T 592—2026) — Type B, PN10 (mm / kg)
| PN | DN | L | H≈ | H1 | t | D | D1 | D2 | d0 | b | n | Th | m | Wt (kg) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 10 | 65 | 115 | 95 | 115 | 9 | 155 | 123 | 104 | 15 | 15 | 6 | M14 | 19 | 12.9 |
| 10 | 80 | 125 | 102 | 125 | 9 | 170 | 138 | 118 | 15 | 15 | 8 | M14 | 23 | 15.1 |
| 10 | 100 | 150 | 116 | 135 | 10 | 190 | 158 | 138 | 15 | 15 | 8 | M14 | 28 | 21.6 |
| 10 | 125 | 175 | 135 | 155 | 10 | 215 | 183 | 164 | 15 | 15 | 10 | M14 | 35 | 32.9 |
| 10 | 150 | 180 | 154 | 160 | 11 | 240 | 208 | 190 | 15 | 16 | 12 | M14 | 42 | 41.2 |
H1 = center-to-end dimension. D = flange OD; D1 = bolt circle; D2 = sealing face dia; d0 = bolt hole dia; b = flange thickness; n = bolt count; m = disc lift. Weight is theoretical, Type B only.
Marine Cast Iron Flanged Check Valves (GB/T 592—2026) — Type B, PN16 (mm / kg)
| PN | DN | L | H≈ | H1 | t | D | D1 | D2 | d0 | b | n | Th | m | Wt (kg) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 16 | 20 | 75 | 66 | 75 | 7 | 95 | 68 | 48 | 13 | 14 | 4 | M12 | 7 | 3.7 |
| 16 | 25 | 80 | 67 | 80 | 7 | 105 | 73 | 56 | 13 | 14 | 4 | M12 | 7 | 4.2 |
| 16 | 32 | 85 | 68 | 85 | 7 | 115 | 83 | 64 | 15 | 15 | 6 | M14 | 9 | 5.2 |
| 16 | 40 | 90 | 75 | 90 | 8 | 125 | 93 | 74 | 15 | 16 | 6 | M14 | 12 | 6.6 |
| 16 | 50 | 95 | 85 | 95 | 8 | 135 | 103 | 84 | 15 | 16 | 6 | M14 | 15 | 8.3 |
Type B structural length tolerance per approved construction drawing. Weight is theoretical, Type B only.
| PN | DN | L | H≈ | H1 | t | D | D1 | D2 | d0 | b | n | Th | m | Wt (kg) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 6 | 50 | 125 | 85 | 125 | 8 | 140 | 110 | 90 | 14 | 16 | 4 | M12 | 15 | 10.0 |
| 6 | 65 | 145 | 95 | 145 | 9 | 160 | 130 | 110 | 14 | 16 | 4 | M12 | 19 | 16.4 |
| 6 | 80 | 155 | 102 | 155 | 9 | 190 | 150 | 128 | 18 | 18 | 4 | M16 | 23 | 20.3 |
| 6 | 100 | 175 | 116 | 175 | 10 | 210 | 170 | 148 | 18 | 18 | 4 | M16 | 28 | 32.2 |
| 6 | 125 | 200 | 135 | 200 | 10 | 240 | 200 | 178 | 18 | 20 | 8 | M16 | 35 | 40.3 |
| 6 | 150 | 225 | 154 | 225 | 11 | 265 | 225 | 202 | 18 | 20 | 8 | M16 | 42 | 56.4 |
Type BS structural length tolerance per GB/T 11698—2026. Weight is theoretical, Type BS only.
| PN | DN | L | H≈ | H1 | t | D | D1 | D2 | d0 | b | n | Th | m | Wt (kg) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 10 | 65 | 145 | 95 | 145 | 9 | 185 | 145 | 122 | 18 | 20 | 4ᵃ | M16 | 19 | 19.0 |
| 10 | 80 | 155 | 102 | 155 | 9 | 200 | 160 | 138 | 18 | 22 | 8 | M16 | 23 | 22.7 |
| 10 | 100 | 175 | 116 | 175 | 10 | 220 | 180 | 158 | 18 | 24 | 8 | M16 | 28 | 30.8 |
| 10 | 125 | 200 | 135 | 200 | 10 | 250 | 210 | 188 | 18 | 26 | 8 | M16 | 35 | 42.3 |
| 10 | 150 | 225 | 154 | 225 | 11 | 285 | 240 | 212 | 22 | 26 | 8 | M20 | 42 | 60.8 |
When using GB/T 9124.1—2019 flange connection, coordinate bolt-hole alignment (manual note a). Weight is theoretical, Type BS only.
Marine Cast Iron Flanged Check Valves (GB/T 592—2026) — Type BS, PN16 (mm / kg)
| PN | DN | L | H≈ | H1 | t | D | D1 | D2 | d0 | b | n | Th | m | Wt (kg) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 16 | 20 | 95 | 66 | 95 | 7 | 105 | 75 | 58 | 14 | 16 | 4 | M12 | 7 | 5.0 |
| 16 | 25 | 100 | 67 | 100 | 7 | 115 | 85 | 68 | 14 | 16 | 4 | M12 | 7 | 5.3 |
| 16 | 32 | 105 | 68 | 105 | 7 | 140 | 100 | 78 | 18 | 18 | 4 | M16 | 9 | 7.3 |
| 16 | 40 | 115 | 75 | 115 | 8 | 150 | 110 | 88 | 18 | 18 | 4 | M16 | 12 | 9.7 |
| 16 | 50 | 125 | 85 | 125 | 8 | 165 | 125 | 102 | 18 | 20 | 4 | M16 | 15 | 12.0 |
Weight is theoretical, Type BS only. Positive weight deviation shall not exceed 4% of design weight.
Marine Cast Iron Flanged Check Valves (GB/T 592—2026) — Type B / BS (Material of Construction)
| Part | Material | Grade | Standard |
|---|---|---|---|
| Body, bonnet | Gray iron | HT200 | GB/T 9439—2023 |
| Body, bonnet | Ductile iron | QT400-18 | GB/T 1348—2019 |
| Disc, bush | Cast tin bronze | ZCuSn10Zn2 | GB/T 1176—2013 |
| Seat | Cast aluminum bronze | ZCuAl9Mn2 | GB/T 1176—2013 |
| Gasket | PTFE | PTFE | QB/T 4041—2010 |
| Gasket | Flexible graphite | RSM | CB/T 3589—1994 |
| Stud | Class 6.8 | 6.8 | GB/T 898—1988 |
| Nut | Class 6 | 6 | GB/T 6170—2015 |
For fuel oil service, gasket and packing shall be flexible graphite. Anti-de-alloying treatment for ZCuAl9Mn2 in seawater available on request.
QA & Testing
Strength — The valve shall withstand the strength test required by GB/T 600—2023 clause 4.14, carried out per clause 5.1.1.3 of the same standard. It is a mandatory item in both type and factory inspection.
Tightness — Seat tightness shall meet GB/T 600—2023 clause 4.15 and be verified per clause 5.1.2.3. Every valve is checked at final inspection, not sampled.
Wall Thickness & Tolerance — Wall thickness follows GB/T 600—2023 clause 4.2, with tolerance per clause 4.5.1; check by thickness gauge, caliper or steel rule (clause 6.3.1). This is a type-inspection item.
Dimensional Tolerance — General dimensions follow GB/T 600—2023 clause 4.5. Structural length tolerance is per the approved drawing for Type B and per GB/T 11698—2026 for Type BS (clause 5.4.3).
Geometric Tolerance — Form and position tolerance shall comply with GB/T 600—2023 clause 4.7, inspected per GB/T 1958 (clause 6.4). Like wall thickness, it is controlled at type-inspection stage.
Assembly & Appearance — Assembly per GB/T 600—2023 clause 4.10 and appearance per clause 4.11 are checked visually or with calipers (clauses 6.5, 6.6). Marking shall comply with GB/T 3032 (clause 5.9).
Weight — Theoretical weight is listed in the dimension tables; positive deviation shall not exceed 4% of design weight (clause 5.8), verified on a scale with 0.01 kg division (clause 6.7). Weight is a negotiated item in factory inspection (Table 5, item 7).
Material Traceability — Each melt shall have at least three heat-numbered test bars retained for no less than three years (clause 5.1.2). This links every casting to its heat and keeps records available for class or owner review.
Inspection Rules — Type inspection uses three samples (clause 7.2); factory inspection is done unit by unit (clause 7.3). Failed items trigger double sampling on retest, or rework followed by reinspection.
Packaging & Storage — Packaging and storage follow GB/T 600—2023 clauses 6.3 and 6.4 (clause 8), so valves arrive protected and ready for shipboard installation.
FAQ
Q1 B or BS — how to match?
Match the mating flange: B = CB/T 4196—2011 (existing ships, domestic build; PN10/PN16 only); BS = GB/T 9124.1—2019 (international new-build; PN6–PN16).
Q2 Angle vs straight — which one?
B/BS turn flow 90° for compact pump-room layouts; A/AS are in-line straight-through. An angle valve adds flow resistance versus straight-through; no pressure-drop figure is specified in this standard, so final sizing follows your system curve.
Q3 Is this a stop check valve?
No. B/BS are plain angle check valves to GB/T 592—2026 — no stem, no handwheel, no throttling or positive shutoff. For shutoff/regulation, use a globe or stop-check series instead.


