Product Categories

  • Marine Anodes
  • Marine Auxiliary Machinery
  • Marine Deck Machinery
  • Marine Decorative Materials
  • Marine Electric Equipment
  • Marine Flanges
  • Marine Galley And Laundry Equipment
  • Marine HVAC Systems
  • Marine Instruments
  • Marine Mooring Equipment
  • Marine Outfitting Equipment
  • Marine Pipe Fittings
  • Marine Propulsion & Shaft & Rudder System
  • Marine pump
  • Marine Safety Equipment-LSA&FFE
  • Marine Valves
  • Container
  • Dredging Equipment
  • Fishing Equipment
  • Lifting&Rigging Equipment
  • Shipbuilding Plate And Section
  • GB/T587 Marine Bronze Flanged Stop Valve Type A/AS

    Overview
    The A/AS series are straight-through, handwheel-operated marine bronze flanged stop valves intended for isolation service in shipboard piping systems handling fresh water, seawater, lube oil, fuel oil, air, and steam up to 250 °C.  A-type valves use flange connection dimensions and sealing faces according to CB/T 4196—2011; AS-type valves use GB/T 9124.1—2019. Across the A/AS range, PN6/PN10/PN16/PN25 and DN15–DN250 are covered depending on type; exact size/pressure combinations are listed in the specification tables.
    The valves use a bronze body, bonnet, disc and packing nut, an aluminium bronze stem, PTFE braided or flexible graphite packing, PTFE or flexible graphite gasket, stainless steel studs/nuts, and a CF8   handwheel with open/close indication. For seawater service, nickel-aluminium bronze is recommended; for fuel oil and steam, flexible graphite packing and gasket should be selected. The standard also notes the de-alloying corrosion risk of aluminium bronze in seawater, and anti-de-alloying treatment can be provided on request.
    The product standard is GB/T 587—2026. Its strength and tightness requirements are specified by reference to GB/T 600—2023, General Specifications for Marine Piping Valves and Fittings, which serves as the general technical basis for marine valve testing. AS-type structural length tolerance follows GB/T 11698—2026; A-type follows the construction drawing. Theoretical weight is based on cast tin bronze, with positive deviation not exceeding 4%; nickel-aluminium bronze is 8% lighter. Castings require at least three heat-numbered test bars per heat, retained for not less than 3 years. Type inspection uses three samples; factory inspection, marking, packaging and storage follow the above standards. Specific clause references and test pressure values are listed in the Compliance & Testing section below.
    Choose the Right Version for Your Piping System
    A Type: Flange dimensions per CB/T 4196—2011. (Traditional marine standard)
    AS Type: Flange dimensions per GB/T 9124.1—2019. (For coordination with GB standard flanges)
    Q1 Material-Cast Tin Bronze (ZCuSn5Pb5Zn5/C83600)
    The standard, cost eftective choice for general marine serice Q1 ofters a wel-balanced combination of moderate stength. good castablity. excelentmachinability, and reliabl resistance to fresh water, seawater. lube oil. fuel oil, air, and steam. It is best suited for low pressure. moderate temperature.and low- velocity piping condtions where the medium is non -aggressive and the valve is not subjected to high mechanical loads or severe erosion Forseaater lines operating at low pressure and ambient temperature. Q1 remains a proven and economical solution. Long term service temperature should not exceed 250°C.
    Q2 Material – Nickel-Aluminium Bronze (ZCuA19Fe4Ni4Mn2 / C95800)
    The upgraded, hgh performance choice for demanding seawater and high pressure service. Q2 ofters significantly higher mechanical strength superioteroson corosion resistance in Rowing seawater, and a weiht reduction of approximately S% compared to O1 Iis best suted for high pressure, hghfow-rate, sand laden, or critical seawater piping conditions where tin bronze would face severe erosion risks or mechanical overload For critical rawseawater lines, O2 is the recommended material by the standard, and anti-de-alloving treatment can be provided on request.


    Type and application scope of Type A / AS stop valves(GB/T 587—2026)
    Type Body design Flange dimensions & sealing face Face-to-face tolerance Service media and temperature Mating flange
    A Straight-through (globe type) CB/T 4196—2011 As specified on the construction drawing  

    Fresh water, sea water, lube oil, fuel oil, air and steam up to 250 °C

    CB-series marine flanges
    AS Straight-through (globe type) GB/T 9124.1—2019 (PN series) GB/T 11698—2026 GB-series steel pipe flanges
    Types B / BS are the angle-pattern versions of the same two flange systems and are not covered here. Strength and tightness per GB/T 600—2023, 4.14 and 4.15; wall thickness 4.2; dimensional tolerances 4.5; geometrical tolerances 4.7.
    Basic parameters, Type A / AS(GB/T 587—2026)
    Type PN Max. working pressure (MPa) Size range (DN) Service media
     

    A

    10 1.0 65 – 250  

     

     

    Fresh water, sea water, lube oil, fuel oil, air; steam up to 250 °C

    16 1.6 125, 150
    25 2.5 20 – 125
     

    AS

    6 0.6 15 – 150
    16 1.6 65 – 150
    25 2.5 15 – 125
    Type A has no PN6 rating; Type AS has no PN10 rating. DN200 and DN250 at PN10 are new in this edition. Body material: Q1 cast tin bronze, Q2 nickel-aluminium bronze.
    Basic dimensions, Type A — CB/T 4196—2011 flanges(GB/T 587—2026)
    PN DN L H≈ t D D1 D2 d0 b n Thread Lift Weight (kg)
     

     

     

     

    10

    65 290 310 6 155 123 104 15 14 6 M14 19 16.4
    80 310 345 6 170 138 118 15 14 8 M14 26 20.6
    100 350 374 6 190 158 138 15 14 8 M14 35 31.6
    125 400 426 7 215 183 164 15 14 10 M14 44 40.0
    150 480 487 7 240 208 190 15 14 12 M14 57 59.5
    200 600 586 8 310 273 250 17 17 12 M16 59 137.0
    250 730 753 9 380 336 310 21 21 14 M20 65 216.0
    16 125 400 465 7 225 187 168 17 19 10 M16 44 56.6
    150 480 524 8 255 217 196 17 19 12 M16 57 66.4
     

     

     

     

     

    25

    20 150 217 5 95 68 48 13 11 4 M12 7 5.4
    25 160 217 5 105 73 56 13 12 4 M12 7 6.1
    32 180 236 5 115 83 64 15 13 6 M14 9 7.2
    40 200 260 5 125 93 74 15 13 6 M14 11 9.7
    50 230 288 6 135 103 84 15 13 6 M14 14 12.3
    65 290 335 7 170 132 110 17 15 8 M16 18 20.5
    80 310 366 7 185 147 126 17 16 8 M16 24 27.4
    100 350 427 8 205 167 146 17 16 10 M20 35 42.0
    125 400 493 9 240 196 172 21 19 10 M20 44 66.6
    Dimensions in mm; weight in kg. L face-to-face length · H≈ centre-to-handwheel height, valve open · t wall thickness · D flange OD · D1 bolt circle dia. · D2 raised face dia. · d0 bolt hole dia. · b flange thickness · n number of bolts · Lift mm. Weights are based on cast tin bronze; deduct 8 % for nickel-aluminium bronze. Positive weight deviation shall not exceed 4 % of the theoretical value.
    Basic dimensions, Type AS — GB/T 9124.1—2019 PN flanges(GB/T 587—2026)
    PN DN L H≈ t D D1 D2 d0 b n Thread Lift Weight (kg)
     

     

     

     

     

     

    6

    15 130 217 4 80 55 40 11 12 4 M10 7 4.8
    20 150 217 4 90 65 50 11 12 4 M10 7 5.6
    25 160 217 4 100 75 60 11 14 4 M10 7 6.3
    32 180 236 5 120 90 70 14 15 4 M12 9 7.5
    40 200 260 5 130 100 80 14 16 4 M12 11 9.6
    50 230 288 5 140 110 90 14 17 4 M12 14 13.2
    65 290 310 6 160 130 110 14 17 4 M12 19 18.9
    80 310 345 6 190 150 128 18 19 4 M16 26 24.9
    100 350 374 6 210 170 148 18 20 4 M16 35 37.1
    125 400 426 7 240 200 178 18 20 8 M16 44 50.0
    150 480 487 7 265 225 202 18 20 8 M16 57 74.7
     

     

    16

    65 290 335 6 185 145 122 18 17 4a M16 18 22.9
    80 310 366 6 200 160 138 18 19 8 M16 24 31.7
    100 350 427 6 220 180 158 18 20 8 M16 35 48.1
    125 400 465 7 250 210 188 18 22 8 M16 44 57.6
    150 480 524 8 285 240 212 22 22 8 M20 57 76.5
     

     

     

     

     

    25

    15 130 217 5 95 65 45 14 12 4 M12 7 5.7
    20 150 217 5 105 75 58 14 12 4 M12 7 6.2
    25 160 217 5 115 85 68 14 14 4 M12 7 6.8
    32 180 236 5 140 100 78 18 15 4 M16 9 9.3
    40 200 260 5 150 110 88 18 16 4 M16 11 11.4
    50 230 288 6 165 125 102 18 17 4 M16 14 16.2
    65 290 335 7 185 145 122 18 17 8 M16 19 23.1
    80 310 366 7 200 160 138 18 19 8 M16 24 31.9
    100 350 427 8 235 190 162 22 20 8 M20 35 51.0
    125 400 493 9 270 220 188 26 26 8 M24 44 80.0
    Dimensions in mm; weight in kg. a Bolt hole alignment to be checked when GB/T 9124.1—2019 flanges are used. The standard prints 113 for b at PN25 DN32–DN50, taken here as 13 (typo in the original). Weights based on cast tin bronze; deduct 8 % for nickel-aluminium bronze. Symbol legend: see Table 4.
    Materials of principal parts(GB/T 587—2026, Table 4)
    Part Material Grade Standard Selection note
    Body, bonnet, disc, gland nut Cast tin bronze ZCuSn5Pb5Zn5 GB/T 1176—2013 Standard choice for fresh water, lube oil and air
    Nickel-aluminium bronze ZCuAl9Fe4Ni4Mn2 Preferred for sea water service
    Stem Aluminium bronze (drawn bar) QAl9-2 GB/T 4423—2020 De-alloying corrosion risk in sea water; resistant treatment available on request
    Packing PTFE braided packing F4SD JB/T 6626—2011 General media
    Flexible graphite RSM CB/T 3589—1994 Fuel oil and steam service
    Gasket PTFE PTFE QB/T 4041—2010 General media
    Flexible graphite RSM CB/T 3589—1994 Fuel oil and steam service
    Stud bolt Stainless steel A4-70 GB/T 3098.6—2023 —
    Nut Stainless steel A4-50 GB/T 3098.15—2023 —
    Handwheel Stainless steel CF8 GB/T 12230—2023 —
    At least 3 test bars with heat numbers shall be kept per heat of casting for not less than 3 years; materials shall be inspected and released before production.

    Quality Assurance And Testing
    Pressure and Sealing Performance:
    Strength and tightness are tested strictly in accordance with GB/T 600—2023 (Clauses 4.14 & 4.15). Factory inspection covers 100% of the valves.
    Dimensional  and Weight Accuracy:
    Wall Thickness and Dimensions: Comply with GB/T 600—2023. AS-type structural length tolerance follows GB/T 11698—2026; A-type follows the provided construction drawing.
    Weight Control: Theoretical weights are based on cast tin bronze. Positive deviation is strictly controlled not to exceed 4%. (If Q2 Nickel-Aluminium Bronze is used, total weight is approximately 8% lighter).
    Material Traceability and Appearance:
    Traceability: Castings are supplied with at least 3 heat-numbered test bars per heat, retained for a minimum of 3 years for quality tracking.
    Visual and Marking: Handwheels feature clear open/close indication (red-painted indicator line). Valve markings strictly follow GB/T 3032.
    Rework and Packaging
    Rework Policy: During factory inspection, any non-conforming valves can be reworked and re-tested. They will only be shipped if they pass the re-test.
    Packaging and Storage: Complies with GB/T 600—2023 (Clauses 6.3 & 6.4), ensuring protection during marine transport and long-term storage.
    Frequently Asked Questions (FAQ)
    Q1: What is the difference between R (Raised Face) and F (Full Face) flange sealing?
    A: R is a raised-face flange, which is the most common for standard marine connections. F  is a full-face flange, typically used for lower pressure or specific piping designs. Please specify R or F in your order.
    Q2: Why does the standard emphasize “de-alloying corrosion” for aluminium bronze stems in seawater?
    A: Aluminium bronze (QAl 9-2) offers excellent strength, but in raw seawater, it may face a specific corrosion risk (de-alloying). For highly critical seawater lines, we recommend selecting the Q2 nickel-aluminium bronze body/bonnet, and anti-de-alloying treatment can be provided for the stem upon request.
    Q3: What is the difference between Q1 and Q2 materials?
    A: Q1 is cast tin bronze (ZCuSn5Pb5Zn5), suitable for general media. Q2 is nickel-aluminium bronze (ZCuAl9Fe4Ni4Mn2), highly recommended for seawater due to its superior corrosion resistance.

    Related Products

    GB Marine Valve

    GB Marine Valves are suitable for common marine media such as fresh water, seawater, fuel oil, lubricating oil, air, and steam. They are primarily used for media shutoff, flow direction control, pressure regulation, and flow control in marine piping systems, and are certified by CCS, ABS, LR, DNV, and others.‌‌

    Send Inquiry

    If you have any questions about our products or services, feel free to reach out to customer service team.

    Scroll to Top