Product Categories

  • Marine Anodes
  • Marine Auxiliary Machinery
  • Marine Deck Machinery
  • Marine Decorative Materials
  • Marine Electric Equipment
  • Marine Flanges
  • Marine Galley And Laundry Equipment
  • Marine HVAC Systems
  • Marine Instruments
  • Marine Mooring Equipment
  • Marine Outfitting Equipment
  • Marine Pipe Fittings
  • Marine Propulsion & Shaft & Rudder System
  • Marine pump
  • Marine Safety Equipment-LSA&FFE
  • Marine Valves
  • Container
  • Dredging Equipment
  • Fishing Equipment
  • Lifting&Rigging Equipment
  • Shipbuilding Plate And Section
  • GB/T588 Marine Bronze Flanged Stop Check Valve Type B/BS

    overview
    Positioning and duty. The B/BS valve is an angle-pattern stop check valve: the disc is guided by the stem for manual shut-off, and closes against reverse flow without any external signal. It is specified for fresh water, seawater, lube oil, fuel oil, air and steam up to 250 °C in ship piping systems, in pressure classes from PN6 to PN25 and sizes from DN15 to DN250. The engineering case for the angle body is layout, not performance — it absorbs the 90° turn that already exists at a bulkhead penetration or a pump discharge, so one valve replaces a bend plus a straight-pattern valve and two flange pairs.
    Why the material split matters. The body, bonnet and disc are cast in either tin bronze (ZCuSn5Pb5Zn5) or nickel-aluminium bronze (ZCuAl9Fe4Ni4Mn2). Tin bronze is the cost-effective answer for fresh water, lube oil, air and low-pressure seawater; nickel-aluminium bronze carries higher initial material cost but is the grade the standard points to for seawater service, and it delivers a lower finished weight. The stem is aluminium bronze QAl9-2 for strength; bolting is A4-70 studs with A4-50 nuts and a CF8 stainless handwheel, so the fasteners do not become the corrosion limit on a bronze body.
    Standards behind it. Design, marking, testing and acceptance follow GB/T 588—2026, with strength, tightness, wall thickness, tolerances, assembly and appearance referenced to GB/T 600—2023. Face-to-face length of the BS type is controlled to GB/T 11698—2026, and every casting heat is backed by three furnace-numbered test bars retained for at least three years. Full dimensional and materials data are in the tables below.
    Quick Selection Guide
    B or BS (flange standard):​
    B type: flange dimensions and sealing face to CB/T 4196—2011. Best suited for replacement and repair on vessels built to Chinese ship piping practice, and for yards already running CB flanges.
    BS type: flange dimensions and sealing face to GB/T 9124.1—2019 (PN series). Recommended when the mating pipe flanges are ordered to the GB PN system.
    These two are not interchangeable. Confirm the mating flange standard before ordering — this is the single most common ordering error on this product.
    Angle (B/BS) or straight (A/AS):​

    Angle pattern: for corners, bulkhead penetrations and pump discharges where the line turns anyway. Saves space and one fitting.
    Straight pattern: for long straight runs and anywhere line pressure margin is tight. The 90° body adds one flow turn, so pressure drop is higher than the straight pattern at the same DN. Where a pressure budget is already tight, take the straight type.
    Body material Q1 or Q2:​

    Q1 tin bronze (ZCuSn5Pb5Zn5)​: for fresh water, lube oil, air  low-pressure/ambient-temperature seawater.It offers reliable, proven performance for general shipboard utility lines, Lower first cost.
    Q2 nickel-aluminium bronze (ZCuAl9Fe4Ni4Mn2)​: for seawater and for critical systems where a shutdown is expensive. Higher initial material cost, offset by longer service life in aggressive media. Note that Q2 parts are about 8% lighter, so the two are not directly comparable on a pure cost-per-kilo basis.
    Packing and gasket P or S:​

    P (PTFE)​: fresh water, seawater, lube oil, air.
    S (flexible graphite)​: mandatory for fuel oil and steam per the standard. Do not substitute PTFE on these media.
    Sealing face R or F:​ match the mating flange — R (raised face) or F (full flat). Mismatched faces leak; they are not a commercial choice.
    Basic Sructure Of Marine Bronze Flanged Stop Check Valve Type B/BS

    Pressure Class and Size Coverage (B / BS)
    Type Flange Standard PN Max Working Pressure (MPa) DN Range
    B CB/T 4196-2011 10 1.0 65 – 250
    B CB/T 4196-2011 16 1.6 125, 150
    B CB/T 4196-2011 25 2.5 20 – 125
    BS GB/T 9124.1-2019 6 0.6 15 – 150
    BS GB/T 9124.1-2019 16 1.6 65 – 150
    BS GB/T 9124.1-2019 25 2.5 15 – 125
     B Type — Structure Dimensions (Unit: mm / kg)
    PN DN L H ≈ H1 Wall Thickness t Handwheel D0 Handwheel S Lift  Weight 
    10 65 115 275 115 6 140 12 17 14.9
    10 80 125 298 125 6 160 14 20 17.9
    10 100 150 315 135 6 180 14 25 24.2
    10 125 175 354 155 7 200 17 32 35.2
    10 150 180 395 160 7 200 17 38 47.9
    10 200 275 460 275 8 360 27 59 99.5
    10 250 325 547 325 9 450 32 65 185.0
    16 125 175 393 155 7 250 22 32 45.1
    16 150 180 433 160 8 280 24 38 58.3
    25 20 75 203 75 5 80 8 7 5.2
    25 25 80 203 80 5 80 8 7 5.8
    25 32 85 216 85 5 100 9 9 6.7
    25 40 90 236 90 5 120 11 11 8.5
    25 50 95 258 95 6 140 12 14 11.0
    25 65 115 301 115 7 160 14 17 18.5
    25 80 125 321 125 7 200 17 20 25.9
    25 100 135 368 135 8 250 22 25 36.1
    25 125 155 421 155 9 280 24 32 55.3

     L = face-to-face (structural length); H ≈ = centre to handwheel top, open; H1 = centre to end face; m = lift; S = handwheel square hole across flats. Weights are for cast tin bronze; reduce by 8 % for nickel-aluminium bronze. Structural length tolerance for B type is per the construction drawing.

     B Type — Flange Connection Dimensions, CB/T 4196-2011 (Unit: mm)
    PN DN D D1 D2 d0 b n Th.
    10 65 155 123 104 15 14 6 M14
    10 80 170 138 118 15 14 8 M14
    10 100 190 158 138 15 14 8 M14
    10 125 215 183 164 15 14 10 M14
    10 150 240 208 190 15 14 12 M14
    10 200 310 273 250 17 17 12 M16
    10 250 380 336 310 21 21 14 M20
    16 125 225 187 168 17 19 10 M16
    16 150 255 217 196 17 19 12 M16
    25 20 95 68 48 13 11 4 M12
    25 25 105 73 56 13 12 4 M12
    25 32 115 83 64 15 13 6 M14
    25 40 125 93 74 15 13 6 M14
    25 50 135 103 84 15 13 6 M14
    25 65 170 132 110 17 15 8 M16
    25 80 185 147 126 17 16 8 M16
    25 100 205 167 146 17 16 10 M16
    25 125 240 196 172 21 19 10 M20
     D = flange OD; D1 = bolt circle; D2 = sealing face diameter; d0 = bolt hole diameter; b = flange thickness; n = number of bolt holes; Th. = thread.
     BS Type — Structure Dimensions (Unit: mm / kg)
    PN DN L H1 H ≈ Wall Thickness t Handwheel D0 Handwheel S Lift  Weight 
    6 15 90 90 203 4 80 8 7 4.7
    6 20 95 95 203 4 80 8 7 5.2
    6 25 100 100 203 4 80 8 7 5.8
    6 32 105 105 216 5 100 9 9 7.2
    6 40 115 115 236 5 120 11 11 9.0
    6 50 125 125 258 5 140 12 14 13.8
    6 65 145 145 275 6 140 12 17 15.2
    6 80 155 155 298 6 160 14 20 23.3
    6 100 175 175 315 6 180 14 25 30.6
    6 125 200 200 354 7 200 17 32 45.7
    6 150 225 225 376 7 200 17 38 63.6
    16 65 145 145 301 6 160 14 19 21.2
    16 80 155 155 321 6 200 17 20 29.9
    16 100 175 175 368 6 250 20 25 41.5
    16 125 200 200 393 7 250 22 32 51.3
    16 150 225 225 433 8 280 24 38 68.9
    25 15 90 90 203 5 80 8 7 5.3
    25 20 95 95 203 5 80 8 7 5.8
    25 25 100 100 203 5 80 8 7 6.7
    25 32 105 105 216 5 100 9 9 8.6
    25 40 115 115 236 5 120 11 11 11.8
    25 50 125 125 258 6 140 12 14 15.4
    25 65 145 145 301 7 160 14 19 21.4
    25 80 155 155 321 7 200 17 20 30.2
    25 100 175 175 368 8 250 20 25 44.0
    25 125 200 200 421 9 280 24 32 64.7
    L and H1 are tabulated separately in the standard and coincide numerically for the BS pattern. Weights are for cast tin bronze; reduce by 8 % for nickel-aluminium bronze. Structural length tolerance for BS type follows GB/T 11698-2026.
    BS Type — Flange Connection Dimensions, GB/T 9124.1-2019 (Unit: mm)
    PN DN D D1 D2 d0 b n Th.
    6 15 80 55 40 11 12 4 M10
    6 20 90 65 50 11 12 4 M10
    6 25 100 75 60 11 14 4 M10
    6 32 120 90 70 14 15 4 M12
    6 40 130 100 80 14 16 4 M12
    6 50 140 110 90 14 17 4 M12
    6 65 160 130 110 14 17 4 M12
    6 80 190 150 128 18 19 4 M16
    6 100 210 170 148 18 20 4 M16
    6 125 240 200 178 18 20 8 M16
    6 150 265 225 202 18 20 8 M16
    16 65 185 145 122 18 17 4 a M16
    16 80 200 160 138 18 19 8 M16
    16 100 220 180 158 18 20 8 M16
    16 125 250 210 188 18 22 8 M16
    16 150 285 240 212 22 22 8 M20
    25 15 95 65 45 14 12 4 M12
    25 20 105 75 58 14 12 4 M12
    25 25 115 85 68 14 14 4 M12
    25 32 140 100 78 18 15 4 M16
    25 40 150 110 88 18 16 4 M16
    25 50 165 125 102 18 17 4 M16
    25 65 185 145 122 18 17 8 M16
    25 80 200 160 138 18 19 8 M16
    25 100 235 190 162 22 20 8 M20
    25 125 270 220 188 26 26 8 M24
    Source: GB/T 588-2026 Table 3 (BS column). a — bolt-hole coordination to be considered when GB/T 9124.1-2019 flanges are used; confirm against the mating flange drawing before production.
    Materials of Construction
    Part Material Grade Standard
    Body, bonnet, disc Cast tin bronze ZCuSn5Pb5Zn5 GB/T 1176-2013
    Body, bonnet, disc Nickel-aluminium bronze ZCuAl9Fe4Ni4Mn2 GB/T 1176-2013
    Stem Aluminium bronze (wrought) QAl9-2 GB/T 4423-2020
    Packing PTFE braided packing F4SD JB/T 6626-2011
    Packing Flexible graphite RSM CB/T 3589-1994
    Gasket PTFE PTFE QB/T 4041-2010
    Gasket Flexible graphite RSM CB/T 3589-1994
    Stud Stainless steel A4-70 GB/T 3098.6-2023
    Nut Stainless steel A4-50 GB/T 3098.15-2023
    Handwheel Stainless steel casting CF8 GB/T 12230-2023
    Quality & Compliance
    trength and tightness:verified per GB/T 588-2026 5.2 / 5.3, which reference GB/T 600-2023 clauses 4.14 and 4.15. Test procedures are 6.1 and 6.2 (GB/T 600-2023 5.1.1.2 and 5.1.2.2). Test pressures follow GB/T 600-2023 — specify them on the datasheet at enquiry rather than assuming a multiplier.
    Wall thickness and tolerances:wall thickness to GB/T 600-2023 4.2, thickness tolerance to 4.5.1, linear dimensional tolerance to 4.5, geometric tolerance to 4.7 checked to GB/T 1958.
    Face-to-face:B pattern per the construction drawing; BS pattern per GB/T 11698-2026. This is the clause that governs whether a replacement valve drops into an existing spool.
    Assembly:per GB/T 600-2023 4.10 (5.6), verified visually and by caliper (6.5). Appearance per 4.11 (5.7).
    Weight:theoretical weight as tabulated; positive deviation must not exceed 4 % of theoretical (5.8). Weighing on a scale with 0.01 kg resolution (6.7). This matters for lifting plans and freight — and it is why we quote per piece, not per kilo.
    Material traceability:each casting heat retains at least 3 numbered test bars with the heat number, kept not less than 3 years (5.1.2). Castings are released by heat; every finished valve is factory-tested individually (7.3.2).
     FAQ
    B or BS — how do I tell which one my line needs?​
    Look at the counter-flange, not at the valve. B uses CB/T 4196-2011 connecting dimensions and sealing face — the marine shipyard pattern. BS uses GB/T 9124.1-2019 — the PN-series steel pipe flange pattern. Same DN and PN does not mean the same drilling; the bolt circle, hole count and thread can all differ. Send us the mating flange drawing (D, D1, hole count, thread, raised or full flat face) and we will confirm the pattern before production. The standard itself flags bolt-hole coordination as a check point for GB/T 9124.1 flanges.
    My space is tight — should I take the angle pattern or the straight one?​
    The angle body turns the flow 90° inside the casting, so it replaces one elbow and the valve: shorter installed envelope, one less flanged joint, one less leak path at bulkheads and corners. The trade-off is real — turning loss plus disc resistance gives a higher pressure drop than a straight-pattern valve of the same DN. On pump discharges with adequate head margin this is normally absorbed; on gravity or low-head lines, run the numbers before you swap a straight valve for an angle one.
    Is this a check valve, or a stop valve?​
    Neither, on its own — this is the combined type, also ordered as an SDNR (screw-down non-return) valve. Closing the handwheel isolates the line; with the handwheel open the disc blocks reverse flow automatically. If you only need manual isolation, specify the GB/T 587 stop valve series; if you only need non-return, specify the GB/T 589 check valve series. 

    Related Products

    GB Marine Valve

    GB Marine Valves are suitable for common marine media such as fresh water, seawater, fuel oil, lubricating oil, air, and steam. They are primarily used for media shutoff, flow direction control, pressure regulation, and flow control in marine piping systems, and are certified by CCS, ABS, LR, DNV, and others.‌‌

    Send Inquiry

    If you have any questions about our products or services, feel free to reach out to customer service team.

    Scroll to Top