Product Categories

  • Marine Anodes
  • Marine Auxiliary Machinery
  • Marine Deck Machinery
  • Marine Decorative Materials
  • Marine Electric Equipment
  • Marine Flanges
  • Marine Galley And Laundry Equipment
  • Marine HVAC Systems
  • Marine Instruments
  • Marine Mooring Equipment
  • Marine Outfitting Equipment
  • Marine Pipe Fittings
  • Marine Propulsion & Shaft & Rudder System
  • Marine pump
  • Marine Safety Equipment-LSA&FFE
  • Marine Valves
  • Container
  • Dredging Equipment
  • Fishing Equipment
  • Lifting&Rigging Equipment
  • Shipbuilding Plate And Section
  • Marine Cast Iron Flanged Stop Valve — B/BS Type, GB/T 590—2026

    Overview
    B and BS are angle-type stop valves turning flow 90° at the shut-off point, removing elbows in tight pipe corners. They handle sea water, fresh water, lube oil and fuel oil up to 1.6 MPa, DN300. Handwheel drive gives positive isolation — not a check valve, stop-check valve or control valve.
    Grey iron (HT200) suits fresh water and lube oil at moderate pressure — the cost-effective default. Recommended when handling raw sea water, larger bores or critical circuits like main engine cooling: choose ductile iron (QT400-18). Its higher initial material cost brings longer service life and lower downtime.
    GB/T 590-2026 governs design, testing and acceptance, with GB/T 600-2023 covering general requirements. Strength, tightness and marking are checked on every unit. Three heat-marked test bars per cast are kept three years for full traceability. Dimensional tolerances stay controlled throughout.
    Quick Selection Guide
    Flange standard — Type B vs Type BS
    Type B conforms to CB/T 4196 — best suited for older vessels and domestic shipyard builds where legacy flange faces must be matched.

    Type BS conforms to GB/T 9124.1 — best suited for international new builds where PN-series flanges are specified.
    Material grade — Q1 (base, HT200 grey iron) vs Q2 (upgraded, QT400-18 ductile iron)​

    Choose Q1 when handling fresh water or lube oil and budget is the primary constraint. It is the cost-effective default for moderate pressure and general auxiliary lines.
    Choose Q2 when handling raw sea water, or when maintenance and downtime costs far exceed the valve’s initial cost. Higher initial material cost buys longer service life — better ROI on critical circuits like main engine cooling.

    Basic Parameters (Table 1) — Type B / BS (PN, MPa, DN)
    Valve Type PN Max Working Pressure (MPa) Nominal Size (DN) Applicable Media
    Type B 10 1.0 65–150 Sea water, fresh water, lube oil, fuel oil
    Type B 16 1.6 20–50 Sea water, fresh water, lube oil, fuel oil
    Type BS 6 0.6 50–300 Sea water, fresh water, lube oil, fuel oil
    Type BS 10 1.0 65–250 Sea water, fresh water, lube oil, fuel oil
    Type BS 16 1.6 20–50 Sea water, fresh water, lube oil, fuel oil

    Type B flanges to CB/T 4196-2011; Type BS flanges to GB/T 9124.1-2019. For fuel oil service, packing and gasket shall be flexible graphite.

    Dimensions & Weight (Table 2) — Type B, PN10 (mm, kg)
    DN L H≈ H1 t D D1 D2 d0 b n Th m Mass 
    65 115 277 115 9 155 123 104 15 15 6 M14 18 16.7
    80 125 304 125 9 170 138 118 15 15 8 M14 24 19.9
    100 150 325 135 10 190 158 138 15 15 8 M14 35 27.2
    125 175 366 155 10 215 183 164 15 15 10 M14 44 37.5
    150 180 415 160 11 240 208 190 15 16 12 M14 57 48.4

    L = face-to-face; H≈ = centre to handwheel, open; H1 = centre to end face; m = travel. Theoretical mass; positive tolerance +4%.

    Dimensions & Weight (Table 2) — Type B, PN16 (mm, kg)
    DN L H≈ H1 t D D1 D2 d0 b n Th m Mass 
    20 75 203 75 7 95 68 48 13 14 4 M12 7 5.1
    25 80 203 80 7 105 73 56 13 14 4 M12 7 5.6
    32 85 216 85 7 115 83 64 15 15 6 M14 9 6.9
    40 90 236 90 8 125 93 74 15 15 6 M14 11 8.5
    50 95 258 95 8 135 103 84 15 16 6 M14 14 11.3
    Dimensions & Weight (Table 3) — Type BS, PN6 (mm, kg)
    DN L H≈ H1 t D D1 D2 d0 b n Th m Mass 
    50 125 258 125 8 140 110 90 14 16 4 M12 14 12.2
    65 145 277 145 9 160 130 110 14 18 4 M12 18 17.7
    80 155 304 155 9 190 150 128 18 18 4 M16 24 21.7
    100 175 325 175 10 210 170 148 18 18 4 M16 35 32.3
    125 200 366 200 10 240 200 178 18 20 8 M16 44 42.8
    150 225 415 225 11 265 225 202 18 20 8 M16 57 55.8
    175 225 489 225 11 295 255 232 18 22 8 M16 60 70.3
    200 275 536 275 11 320 280 258 18 22 8 M16 68 95.6
    250 325 605 325 13 375 335 312 22 24 12 M20 80 151.0
    300 375 672 375 13 440 395 365 22 24 12 M20 100 207.0
    Dimensions & Weight (Table 3) — Type BS, PN10 (mm, kg)
    DN L H≈ H1 t D D1 D2 d0 b n Th m Mass 
    65 145 277 145 9 185 145 122 18 20 4 M16 18 20.1
    80 155 304 155 9 200 160 138 18 22 4 M16 24 23.9
    100 175 325 175 10 220 180 158 18 24 4 M16 35 32.8
    125 200 366 200 10 250 210 188 18 24 8 M16 44 44.6
    150 225 415 225 11 285 240 212 22 26 8 M20 57 59.8
    175 225 489 225 11 315 270 242 22 26 8 M20 60 73.8
    200 275 543 275 11 340 295 268 22 28 8 M20 68 99.6
    250 325 623 325 13 395 350 320 22 28 12 M20 80 153.0

    Dimensions & Weight (Table 3) — Type BS, PN16 (mm, kg)

    DN L H≈ H1 t D D1 D2 d0 b n Th m Mass 
    20 95 203 95 7 105 75 58 14 16 4 M12 7 5.7
    25 100 203 100 7 115 85 68 14 16 4 M12 7 6.4
    32 105 216 105 7 140 100 78 18 18 4 M16 9 8.7
    40 115 236 115 8 150 110 88 18 18 4 M16 11 10.7
    50 125 258 125 8 165 125 102 18 20 4 M16 14 14.2
    Material of Construction (Table 4) — Type B / BS
    Part Name Material Material Grade Standard
    Body, bonnet Grey iron HT200 GB/T 9439-2023
    Body, bonnet Ductile iron QT400-18 GB/T 1348-2019
    Disc Cast tin bronze ZCuSn10Zn2 GB/T 1176-2013
    Stem Aluminium bronze QAl9-2 GB/T 4423-2020
    Seat Cast aluminium bronze ZCuAl9Mn2 GB/T 1176-2013
    Packing PTFE braided packing F4SD JB/T 6626-2011
    Packing Flexible graphite RSM CB/T 3589-1994
    Gasket PTFE PTFE QB/T 4041-2010
    Gasket Flexible graphite RSM CB/T 3589-1994
    Fasteners — stud — Class 6.8 GB/T 898-1988
    Fasteners — nut — Class 6 GB/T 6170-2015
    Handwheel Cast steel ZG230-450 CB/T 3530-1993
    Handwheel Ductile iron QT400-15 CB/T 3530-1993
    For fuel oil media, packing and gasket shall be flexible graphite. Anti-de-alloying treatment of aluminium bronze for seawater service is available on request.QA & Testing
    1. Inspection framework

    Every valve is released under GB/T 590-2026, with general marine valve requirements from GB/T 600-2023. Verification splits into type approval and routine factory release, covering both design conformity and unit-to-unit consistency.
    2. Pressure integrity
    Strength (GB/T 600-2023 §4.14) and tightness (§4.15) are tested under GB/T 590-2026 §6.1 and §6.2 (GB/T 600-2023 §5.1.1.1 and §5.1.2.1). Both are compulsory on every unit — no valve ships without passing them. A failed type-approval sample triggers doubled sampling; factory units may be reworked and re-verified.
    3. Dimensional and geometrical control
    Wall thickness follows GB/T 600-2023 §4.2, tolerance §4.5.1. Dimensional tolerance follows §4.5; form and position tolerance §4.7, inspected per GB/T 1958. Face-to-face tolerance is taken from the approved drawing for Type B and from GB/T 11698-2026 for Type BS.
    4. Material traceability
    Each cast heat keeps at least three heat-marked test bars for no less than three years (§5.1.2). Material is released for production only after inspection — traceability from heat to finished valve for class survey or procurement audit.
    5. Mass tolerance
    Theoretical mass is listed per size in the dimension tables. Actual mass may exceed it by no more than 4% (§5.8), verified on a scale with a graduation of 0.01 kg or finer (§6.7).
    6. Inspection regimes
    Type approval uses three samples and covers all eight items in Table 5. Routine factory inspection is unit by unit, except material by heat batch. Strength, tightness, assembly, appearance and marking are compulsory; mass is by agreement; dimensional and geometrical checks apply at type approval only.
    7. Marking, packaging and storage
    Marking follows GB/T 3032 (§5.9), verified visually (§6.8). Packaging and storage follow GB/T 600-2023 §6.3 and §6.4.

    Related Products

    GB Marine Valve

    GB Marine Valves are suitable for common marine media such as fresh water, seawater, fuel oil, lubricating oil, air, and steam. They are primarily used for media shutoff, flow direction control, pressure regulation, and flow control in marine piping systems, and are certified by CCS, ABS, LR, DNV, and others.‌‌

    Send Inquiry

    If you have any questions about our products or services, feel free to reach out to customer service team.

    Scroll to Top