Product Categories

  • Marine Anodes
  • Marine Auxiliary Machinery
  • Marine Deck Machinery
  • Marine Decorative Materials
  • Marine Electric Equipment
  • Marine Flanges
  • Marine Galley And Laundry Equipment
  • Marine HVAC Systems
  • Marine Instruments
  • Marine Mooring Equipment
  • Marine Outfitting Equipment
  • Marine Pipe Fittings
  • Marine Propulsion & Shaft & Rudder System
  • Marine pump
  • Marine Safety Equipment-LSA&FFE
  • Marine Valves
  • Container
  • Dredging Equipment
  • Fishing Equipment
  • Lifting&Rigging Equipment
  • Shipbuilding Plate And Section
  • B/BS Type Marine Cast Iron Flanged Check Valves — GB/T 592—2026

    Overview
    B and BS are angle-type flanged check valves to GB/T 592—2026 for marine seawater, fresh water, lube oil and fuel oil lines. They turn flow 90° and close on reverse flow, protecting pumps in tight pump-room layouts. The center-to-end dimension sets the mounting envelope; check it before piping.
    Body selection follows the duty. HT200 gray iron is the cost-effective default for fresh water and lube oil at normal duty. QT400-18 ductile iron suits higher shock loads, where longer service life offsets a higher initial material cost. Tin bronze trim resists wear; the aluminum-bronze seat needs de-alloying control in seawater.
    All valves are built and verified to GB/T 592—2026 against GB/T 600—2023. Strength, tightness, dimensions and assembly are checked under one controlled system. Each melt keeps at least three marked test bars for three years, giving full traceability for class and owner review.
    Quick Selection Guide
    Flange standard — B vs BS
    Type B: CB/T 4196—2011 flange. 
    Type BS: GB/T 9124.1—2019 flange.
    Body material — HT200 vs QT400-18
    HT200 gray iron: cost-effective default for fresh water / lube oil, normal duty.
    QT400-18 ductile iron: recommended when shock load and mechanical margin dominate, or when downtime cost exceeds initial material cost.

     

     

     

     

     

     

    Marine Cast Iron Flanged Check Valves (GB/T 592—2026) — Type B / BS (Basic Parameters)
    Type PN Max working pressure (MPa) DN Medium Flange standard
    B 10 1.0 65–150 Sea water / fresh water / lube oil / fuel oil CB/T 4196—2011
    B 16 1.6 20–50 Sea water / fresh water / lube oil / fuel oil CB/T 4196—2011
    BS 6 0.6 50–150 Sea water / fresh water / lube oil / fuel oil GB/T 9124.1—2019
    BS 10 1.0 65–150 Sea water / fresh water / lube oil / fuel oil GB/T 9124.1—2019
    BS 16 1.6 20–50 Sea water / fresh water / lube oil / fuel oil GB/T 9124.1—2019

    Note: For fuel oil service, gasket and packing shall be flexible graphite. Type B has no PN6 rating. Dimensions in mm; pressure in MPa.

    Marine Cast Iron Flanged Check Valves (GB/T 592—2026) — Type B, PN10 (mm / kg)

    PN DN L H≈ H1 t D D1 D2 d0 b n Th m Wt (kg)
    10 65 115 95 115 9 155 123 104 15 15 6 M14 19 12.9
    10 80 125 102 125 9 170 138 118 15 15 8 M14 23 15.1
    10 100 150 116 135 10 190 158 138 15 15 8 M14 28 21.6
    10 125 175 135 155 10 215 183 164 15 15 10 M14 35 32.9
    10 150 180 154 160 11 240 208 190 15 16 12 M14 42 41.2

    H1 = center-to-end dimension. D = flange OD; D1 = bolt circle; D2 = sealing face dia; d0 = bolt hole dia; b = flange thickness; n = bolt count; m = disc lift. Weight is theoretical, Type B only.

    Marine Cast Iron Flanged Check Valves (GB/T 592—2026) — Type B, PN16 (mm / kg)

    PN DN L H≈ H1 t D D1 D2 d0 b n Th m Wt (kg)
    16 20 75 66 75 7 95 68 48 13 14 4 M12 7 3.7
    16 25 80 67 80 7 105 73 56 13 14 4 M12 7 4.2
    16 32 85 68 85 7 115 83 64 15 15 6 M14 9 5.2
    16 40 90 75 90 8 125 93 74 15 16 6 M14 12 6.6
    16 50 95 85 95 8 135 103 84 15 16 6 M14 15 8.3

    Type B structural length tolerance per approved construction drawing. Weight is theoretical, Type B only.

    Marine Cast Iron Flanged Check Valves (GB/T 592—2026) — Type BS, PN6 (mm / kg)
    PN DN L H≈ H1 t D D1 D2 d0 b n Th m Wt (kg)
    6 50 125 85 125 8 140 110 90 14 16 4 M12 15 10.0
    6 65 145 95 145 9 160 130 110 14 16 4 M12 19 16.4
    6 80 155 102 155 9 190 150 128 18 18 4 M16 23 20.3
    6 100 175 116 175 10 210 170 148 18 18 4 M16 28 32.2
    6 125 200 135 200 10 240 200 178 18 20 8 M16 35 40.3
    6 150 225 154 225 11 265 225 202 18 20 8 M16 42 56.4

    Type BS structural length tolerance per GB/T 11698—2026. Weight is theoretical, Type BS only.

    Marine Cast Iron Flanged Check Valves (GB/T 592—2026) — Type BS, PN10 (mm / kg)
    PN DN L H≈ H1 t D D1 D2 d0 b n Th m Wt (kg)
    10 65 145 95 145 9 185 145 122 18 20 4ᵃ M16 19 19.0
    10 80 155 102 155 9 200 160 138 18 22 8 M16 23 22.7
    10 100 175 116 175 10 220 180 158 18 24 8 M16 28 30.8
    10 125 200 135 200 10 250 210 188 18 26 8 M16 35 42.3
    10 150 225 154 225 11 285 240 212 22 26 8 M20 42 60.8

     When using GB/T 9124.1—2019 flange connection, coordinate bolt-hole alignment (manual note a). Weight is theoretical, Type BS only.

    Marine Cast Iron Flanged Check Valves (GB/T 592—2026) — Type BS, PN16 (mm / kg)

    PN DN L H≈ H1 t D D1 D2 d0 b n Th m Wt (kg)
    16 20 95 66 95 7 105 75 58 14 16 4 M12 7 5.0
    16 25 100 67 100 7 115 85 68 14 16 4 M12 7 5.3
    16 32 105 68 105 7 140 100 78 18 18 4 M16 9 7.3
    16 40 115 75 115 8 150 110 88 18 18 4 M16 12 9.7
    16 50 125 85 125 8 165 125 102 18 20 4 M16 15 12.0

    Weight is theoretical, Type BS only. Positive weight deviation shall not exceed 4% of design weight.

    Marine Cast Iron Flanged Check Valves (GB/T 592—2026) — Type B / BS (Material of Construction)

    Part Material Grade Standard
    Body, bonnet Gray iron HT200 GB/T 9439—2023
    Body, bonnet Ductile iron QT400-18 GB/T 1348—2019
    Disc, bush Cast tin bronze ZCuSn10Zn2 GB/T 1176—2013
    Seat Cast aluminum bronze ZCuAl9Mn2 GB/T 1176—2013
    Gasket PTFE PTFE QB/T 4041—2010
    Gasket Flexible graphite RSM CB/T 3589—1994
    Stud Class 6.8 6.8 GB/T 898—1988
    Nut Class 6 6 GB/T 6170—2015

    For fuel oil service, gasket and packing shall be flexible graphite. Anti-de-alloying treatment for ZCuAl9Mn2 in seawater available on request.
    QA & Testing
    Strength — The valve shall withstand the strength test required by GB/T 600—2023 clause 4.14, carried out per clause 5.1.1.3 of the same standard. It is a mandatory item in both type and factory inspection.
    Tightness — Seat tightness shall meet GB/T 600—2023 clause 4.15 and be verified per clause 5.1.2.3. Every valve is checked at final inspection, not sampled.
    Wall Thickness & Tolerance — Wall thickness follows GB/T 600—2023 clause 4.2, with tolerance per clause 4.5.1; check by thickness gauge, caliper or steel rule (clause 6.3.1). This is a type-inspection item.
    Dimensional Tolerance — General dimensions follow GB/T 600—2023 clause 4.5. Structural length tolerance is per the approved drawing for Type B and per GB/T 11698—2026 for Type BS (clause 5.4.3).
    Geometric Tolerance — Form and position tolerance shall comply with GB/T 600—2023 clause 4.7, inspected per GB/T 1958 (clause 6.4). Like wall thickness, it is controlled at type-inspection stage.
    Assembly & Appearance — Assembly per GB/T 600—2023 clause 4.10 and appearance per clause 4.11 are checked visually or with calipers (clauses 6.5, 6.6). Marking shall comply with GB/T 3032 (clause 5.9).
    Weight — Theoretical weight is listed in the dimension tables; positive deviation shall not exceed 4% of design weight (clause 5.8), verified on a scale with 0.01 kg division (clause 6.7). Weight is a negotiated item in factory inspection (Table 5, item 7).
    Material Traceability — Each melt shall have at least three heat-numbered test bars retained for no less than three years (clause 5.1.2). This links every casting to its heat and keeps records available for class or owner review.
    Inspection Rules — Type inspection uses three samples (clause 7.2); factory inspection is done unit by unit (clause 7.3). Failed items trigger double sampling on retest, or rework followed by reinspection.
    Packaging & Storage — Packaging and storage follow GB/T 600—2023 clauses 6.3 and 6.4 (clause 8), so valves arrive protected and ready for shipboard installation.
    FAQ
    Q1 B or BS — how to match?​
    Match the mating flange: B = CB/T 4196—2011 (existing ships, domestic build; PN10/PN16 only); BS = GB/T 9124.1—2019 (international new-build; PN6–PN16).
    Q2 Angle vs straight — which one?​
    B/BS turn flow 90° for compact pump-room layouts; A/AS are in-line straight-through. An angle valve adds flow resistance versus straight-through; no pressure-drop figure is specified in this standard, so final sizing follows your system curve.
    Q3 Is this a stop check valve?​
    No. B/BS are plain angle check valves to GB/T 592—2026 — no stem, no handwheel, no throttling or positive shutoff. For shutoff/regulation, use a globe or stop-check series instead.

    Related Products

    GB Marine Valve

    GB Marine Valves are suitable for common marine media such as fresh water, seawater, fuel oil, lubricating oil, air, and steam. They are primarily used for media shutoff, flow direction control, pressure regulation, and flow control in marine piping systems, and are certified by CCS, ABS, LR, DNV, and others.‌‌

    Send Inquiry

    If you have any questions about our products or services, feel free to reach out to customer service team.

    Scroll to Top